Satellite Internet forum
https://www.satsig.net/cgi-bin/yabb/YaBB.pl
VSAT technology and installation >> iDirect Forum: hubs and terminals >> Option file in depth
https://www.satsig.net/cgi-bin/yabb/YaBB.pl?num=1282747019

Message started by nkast on Aug 25th, 2010 at 3:36pm

Title: Option file in depth
Post by nkast on Aug 25th, 2010 at 3:36pm
HI Gurus,

Here is option file for the site: Can anybody explain each line item

[OPTIONS_FILE]
     product_mode = idirect_scpc
     modem_sn = xxxxx
     generated_by = NMS-10.0.1
     did = xxxxx
     modem_type = Remote
     modem_hardware = 3100
     is_mesh = 0
     disable_options_flash_command = 0
     carrier_type = 0

[SECURITY]
     password = $idi3$.JjXsv$.FmLfsGbDHOa1WxeIRSzpRe2Ufo7sTb6cjEcp7979jptlUNd53gu/n9bYB.3u/BU0Akg2Zou0jOd3BKs3Vfgr1
     admin_password = $idi3$./mm6s$/dFQgfOEsPCX5mA4zB/wU5q0x6ZOLx5mV9J0ie0t1WkhaiFf0aol868xwrzNy3XNo9DeJXOlWDQAysy0VsjTSo
     os_password = $1$/1/C/g$tR.kh2FYbDKDxL0aWx5tn.

[NMS]
     timeout = 20000
     server_ip = xxxxx
     broadcast_ip = xxxxx
     keep_alive_port_number = 2860
     NRD_server_ip = xxxxx
     NRD_remote_status_port_number = 2859
     service_monitor_interval = 1000
     download_monitor_group = xxxxx
     download_monitor_port = 9000
     download_monitor_credentials = 1
     is_nms_managed = 1
     event_server_ip = xxxxx
     event_server_port = 2860

[VLAN]
     mode = 0
     vid = 1

[ETH0_1]
     address = xxxxx
     netmask = xxxxx
     rip_enabled = 0

[DNS_1]
     dns_enable = 1
     dns_primary_server_name = ns1
     dns_primary_server_addr = 4.2.2.1
     dns_secondary_server_name = ns2
     dns_secondary_server_addr = 4.2.2.2
     dns_cache_size = 100
     dns_cache_ttl_min = 300
     dns_cache_ttl_max = 86400
     dns_forward_queue_size = 1000
     dns_forward_timeout = 2000

[ROUTE_1_0]
     interface = sat0
     network = 0.0.0.0
     netmask = 0.0.0.0
     gateway = 0.0.0.0
     metric = 1

[SAT0_1]
     address = xxxxxx
     netmask = 255.255.255.248
     rip_enabled = 0

[ETH0]
     interface = ixp0
     phy_count = 1

[LAN]
     lan_ip = xxxxxx
     lan_subnet_ip = 255.255.255.248
     lan_gw_ip = 0.0.0.0

[MODEM_PARAMETERS]
     rx_freq = 1379024999
     rx_acqrange = 66000
     rx_bitrate = 9100000
     rx_mode = 2
     rx_modtype = 1
     rx_fecrate = 15
     rx_scram = 1
     rx_diff = 0
     rx_specinv = 0
     tx_freq = 1000000000
     tx_bitrate = 336000
     tx_mode = 0
     tx_modtype = 1
     tx_clksource = 0
     tx_fecrate = 5
     tx_scram = 1
     tx_diff = 0
     tx_specinv = 0
     tx_power_in_dbm = -5.000000
     rx_fsd = 28796
     tx_spreading_factor = 1
     rx_spreading_factor = 1
     tx_spread_enable = 0
     rx_spread_enable = 0
     is_demod2_active = 0
     rx_symrate = 5736164.973838
     tx_symrate = 254485

[ACQUISITION_PARAMETERS]
     fsd = 29285

[UCP]
     power_uplink_control_processing = 1
     max_power_level_in_db = 0.000000

[ODU]
     music_present = 0
     odu_rx_dc_power = 1
     odu_rx_10_mhz = 0
     odu_tx_dc_power = 1
     odu_tx_10_mhz = 1
     lnb_tone_enable = 0
     lnb_dc_voltage = 19
     odu_disable_tx_pwm = 0

[TDMA]
     tx_watchdog_timeout_in_frames = 2

[TIMEPLAN]
     fec_blocks_per_outroute_frame = 351
     unique_word_len_downstream = 32
     symbols_per_inroute_frame = 31893
     outroute_fec_block_len = 512
     outroute_fec_type = 793
     inroute_fec_block_len = 128
     inroute_fec_type = 660
     unique_word_len = 32
     symbols_per_outroute_frame = 718879
     num_acq_slots = 1
     aperture_traffic = 8
     aperture_acq = 437
     num_traffic_slots = 56
     payload = 512
     scaling_factor = 0
     skip_slots = 2


[FREQ_TRANS]
     down_translation = 10750.000000
     up_translation = 13050.000000

[DEBUG]
     cpu_util_test_enabled = 0

[GUI_SERVER_PROXY]
     port = 14599

[POWER_MANAGEMENT]
     enable = 0
     sleep_timeout = 0

[ENC]
     enc_layer_enabled = 0
     enc_enabled = 0
     enc_mode = 0
     peer_mode = 1
     auth_level_required = 0

[NET_ENC]
     id = 1
     is_encrypted = 0

[UDP]
     passthru = 1
     force_udp_fullheader = 1
     force_rtp_fullheader = 1
     payload_comp = 0
     max_hdr_comp_packet_size = 180

[COMPRESSION]
     Threshold = 90

[OOB]
     mem_low_percent = 75
     mem_high_percent = 90

[TX]
     device_path = /dev
     device_mode = tdma
     device_name = tx

[RX1]
     device_path = /dev
     device_mode = scpc
     device_name = rx1

[BTP]
     device_path = /dev
     device_mode = tdma
     device_name = btp

[SOF]
     device_path = /dev
     device_mode = tdma
     device_name = sof

[BTP_REQ]
     device_path = /dev
     device_mode = tdma
     device_name = btp_req

[TX_SOF]
     device_path = /dev
     device_mode = tdma
     device_name = tx_sof

[SATELLITE]
     min_look_angle = 0.000000

[SYSTEM_TRAY]
     mode = 1
     server = 10.200.22.4
     port = 2859
     interval = 5000
     service_monitor_group = xxxxx
     service_monitor_port = 9001


Title: Re: Option file in depth
Post by imNAK on Aug 31st, 2010 at 5:45pm
hello ,
i will explain but not with full detalis caz its too much
1- [OPTIONS_FILE]
here is your modem genral info serial number pakge version  men hardware and software ifo
2-[SECURITY]
user name and passowrd the user name normaly admin
and for user possible to change the password
3-[NMS]
Planning for a Network Management System
Effective planning for a network management system requires that a number of network management tasks be performed. The network management system should discover the network inventory, monitor the health and status of devices and provide alerts to conditions that impact system performance.

NMS systems make use of various protocols for the purpose they serve. For example, SNMP protocol allows them to simply gather the information from the various devices down the network hierarchy. NMS software is responsible for identification of the problem, the exact source of the problem and solving them. The NMS systems not only are responsible for the detection of faults but also for collecting the statistics of the devices over a period of time. They may include a library where the previous network statistical data over a period of time is stored along with the problems and the solutions that worked in the past. This library can come useful in case a fault is found. NMS software can consult the library and search for the best possible method to resolve the problem.
4-[VLAN]
A virtual LAN, commonly known as a VLAN, is a group of hosts with a common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of their physical location. A VLAN has the same attributes as a physical LAN, but it allows for end stations to be grouped together even if they are not located on the same network switch. Network reconfiguration can be done through software instead of physically relocating devices.
5-[ETH0_1]
This line ... You'll be setting up a static public IP on eth0 and a static private IP on eth0:1
6-[DNS_1]
The Domain Name System (DNS) is a distributed hierarchical naming system for computers, services, or any resource connected to the Internet or a private network. It associates various information with domain names assigned to each of the participants. Most importantly, it translates domain names meaningful to humans into the numerical (binary) identifiers associated with networking equipment for the purpose of locating and addressing these devices worldwide. An often-used analogy to explain the Domain Name System is that it serves as the "phone book" for the Internet by translating human-friendly computer hostnames into IP addresses.

Title: Re: Option file in depth
Post by fluffymassive on Sep 1st, 2010 at 8:27am
This is where your BUC/LNB LO translations are.
[FREQ_TRANS]
     down_translation = 10750.000000 --- LNB LO
     up_translation = 13050.000000 ----BUC LO

This tells the modem what the receive frequency is in L-Band (1379.0249MHz) and the carrier bandwidth. The tx_freq will stay at 1000000 until the modem receives the timeplan on which to transmit from the hub.
[MODEM_PARAMETERS]

Title: Re: Option file in depth
Post by ITCITY GLOBALCOMMUNICATIONS on Sep 1st, 2010 at 10:49am
What is your root and admin Password.

With this new 10.0.1 you cant cant change your root password .

Powered by YaBB 2.5.2!
YaBB Forum Software © 2000-. All Rights Reserved.