Satellite Internet forum
https://www.satsig.net/cgi-bin/yabb/YaBB.pl
VSAT technology and installation >> HughesNet and Hughes HX VSATs >> Hughes HN7000S Dish Alignment Help
https://www.satsig.net/cgi-bin/yabb/YaBB.pl?num=1284796910

Message started by patrickjdoran on Sep 18th, 2010 at 9:01am

Title: Hughes HN7000S Dish Alignment Help
Post by patrickjdoran on Sep 18th, 2010 at 9:01am
Need help aligning a Hughes HN7000S system in Ramadi, Iraq. I was told i was aiming at Eutelsat W2A
10 East. The service provider i am using is ATS Iraq.
Here are the parameters given to me:
Satellite Longitude      10 Degrees East
Satellite Frequency      16040
Symbol Rate             15000000
LNB 22KHz Switch      On
DVB Mode            DVB S2 ACM
Frequency Band            KU/QPSK
Receive Pol            Vertical
Transmit Pol            Horizontal
VSAT LAT Degrees            34 98
VSAT LAT Minutes            59.1
VSAT LAT Hemisphere             NORTH
VSAT LONG Degrees             44.11
VSAT LONG Minutes             6.8
VSAT LONG Hemisphere             EAST
Dish azimuth (deg E relative to true north)            229.75
Dish azimuth (deg E relative to magnetic north)      225.35
Dish elevation (deg)                        35.66
Slant range (km)                              38126.33
Polarisation tilt (deg)                        38.71
Polar mount main axis angle (deg)                  35.66
Polar mount dish offset tilt (deg)                  4.96

Any help that can be given me would be great. Thank You.

Sgt Patrick Doran E3/15 INF

Title: Re: Hughes HN7000S Dish Alignment Help
Post by A.Walker on Sep 18th, 2010 at 9:47am
Hi the problem you have is W2 is a very low elevation for Afghan , we have a Hughes HX service on 3 Satellites over Afghan with much higherb elevation and could offer you a modem swap if you wanted to come over to our service , if so please contact sales@bentleywalker.com

Title: Re: Hughes HN7000S Dish Alignment Help
Post by patrickjdoran on Sep 18th, 2010 at 11:20am
A.Walker - Sory but i am not in Afghanistan. I'm in Ar Ramadi, Iraq.

Title: Re: Hughes HN7000S Dish Alignment Help
Post by USN - Retired on Sep 18th, 2010 at 12:08pm
I don't know which outdoor equipments you're using, nor do I know your exact location. But it's not necessary to post what might be classified information. So I'll just point out what I see as possible discrepancies on that parameter sheet you posted. First I am wondering if it's actually necessary to have 22Khz ON.

Next is the VSAT LAT and LONG data. The HN7000S does require the user to enter his Lat/Lon in decimal format, but decimal degrees only. The fact you list decimal degrees AND decimal minutes puts the accuracy of the Az/EL/Pol numbers in question. Just using the Wikipedia coordinates for Ramadi, I calculate your pointing angles to be 225.8 Az (mag), 37.3 El, 39.8 Pol. Unless you have an offset dish mount that is, which requires a further adjustment to the elevation number. The offset in degrees of your dish mount (if any) should be listed in the hardware manual as well.

So for the moment, let's approach this from an antenna pointing viewpoint. Please confirm in your hardware manual whether or not the 22 Khz should be ON or OFF. Then determine what - if any - the offset (in degrees) is for your dish mount. Finally, clarify your geographic coordinates into xx.xxx degree format (turn minutes into decimal degrees).

//greg//


Title: Re: Hughes HN7000S Dish Alignment Help
Post by Eric Johnston on Sep 18th, 2010 at 1:58pm
As Greg suggests, it would be helpful to tell us what outdoor equipment you have.  What is the LNB type ?
If it is LNB P/N 1500287-0001 (NJR2784HH) then it has a fixed local oscillator frequency of 10 GHz and the 22 kHz tone from the modem is not required.
Ref: https://mc.njr.co.jp/eng/products/vsat/ku-lnb/dro900.html

If you don't have the HN7000S installation manual then note this important warning:
Do not interfere with the two coax cables or the multiway low voltage connector between the power supply and the modem unless the mains wall switch is OFF.  Always power OFF at the mains wall switch before working on the coax cables.

During your initial satellite finding and pointing activities it is suggested that you have only one coax cable connected from the LNB to the modem receive input.

Useful references:
HN7000S-HN7700S-Remote-Terminal-Installation-Guide ( 9 Mbytes )
HN7000S-HN7700S-Remote-Terminal-User-Guide ( 5 Mbytes )
HN7000S-Quick-Start-Guide ( 307k bytes )

If you have a simple discrete LNB module (like NJR2784) on a filter sidearm then for vertical receive polarisation start with the LNB sticking out sideways on the left, as viewed with you standing behind the dish and facing forwards towards the satellite in the sky.  Then apply the +ve polarisation adjustment amount by turning it clockwise by the calculated amount, still as viewed with you standing behind the dish and facing forwards towards the satellite in the sky.

Best regards, Eric.

Title: Re: Hughes HN7000S Dish Alignment Help
Post by patrickjdoran on Sep 18th, 2010 at 5:09pm
Gentlemen the LNB i have is NJR2784HH. I don't not know what outdoor system it is. How do i add pics to the post so i can show you what system it is?

Title: Re: Hughes HN7000S Dish Alignment Help
Post by Forum Admin on Sep 18th, 2010 at 6:09pm
Send images by email to eric@satsig.net and I will insert them here.

Alternatively, edit the pictures to make them small file sizes (i.e. crop and save in low jpg resolution); upload to a public server somewhere and insert into your messge like so:
{img}https://www.example.com/images/dish-picture-1.jpg{/img}
Use square brackets not squiggly ones !

Best regards, Eric.

Title: Re: Hughes HN7000S Dish Alignment Help
Post by Forum Admin on Sep 18th, 2010 at 11:48pm
You have a simple discrete LNB module (NJR2784) on a filter side arm, so the following applies:

For vertical receive polarisation start with the LNB sticking out sideways on the left, as viewed with you standing behind the dish and facing forwards towards the satellite in the sky.  Then apply the +ve polarisation adjustment amount by turning it clockwise by the calculated amount, still as viewed with you standing behind the dish and facing forwards towards the satellite in the sky.  



These images above show the wrong polarisation setting.
You have started with the LNB filter arm upwards (Horizontal polarisation) and then applied approx +45 deg clockwise adjustment.
Instead, for Vertical receive polarisation and an adjustment of +39 deg, you need to start with the LNB filter arm to the left and then turn it +39 deg clockwise. Remember always viewed from behind the dish and facing forwards towards the satellite in the sky. It is the amount of adjustment that matters, not the actual scale reading, which may go backwards from 90 deg. e.g. a 51 deg marking is  39 deg back from 90
For the W2A satellite it may help to set the polarisation a further +3 deg clockwise.

The picture below from page https://www.satsig.net/maps/satellite-dish-pointing-iraq.htm shows you the pointing angles, the blue azimuth line towards nearby landmarks or buildings (increase the scale and go to your exact location) plus a picture of what your LNB should look like - viewed with you standing behind the dish and facing towards the feed and the satellite in the sky.


The beam elevation angle is about 39 deg, which is about right. It helps if the pole is upright and the clamps tight.  If the clamps are a little loose try setting a beam elevation angle on the scale a couple of degrees higher than calculated.

To find the satellite observe the SQF reading on the PC screen and the RX LED on the modem.  Swing the dish boldly till you get a response. If nothing on the first swing alter the elevation in 1 or 2 deg steps.

Once you find any satellite note the position and peak up.  If the maximum is 29 you have the wrong satellite or have put the wrong configuration (frequency or symbol rate). Expect a figure like 91.  Peak up to the maximum.  Once you have found a satellite, note that the adjacent satellites alonmg the orbit will be to the upper left and lower right, as viewed towards the sky.
wxw
Best regards, Eric.

Title: Re: Hughes HN7000S Dish Alignment Help
Post by USN - Retired on Sep 19th, 2010 at 12:58am
Keep in mind that the pointing angles provided are calculated (theoretical) numbers, intended only as starting points. The odds of them actually obtaining an optimized signal "right outa the box" are very low, and are really only intended to get you in the ballpark. Even the hash marks on the equipment are gross indicators. You start with the calculated numbers - use them to find the satellite signal - then fine tune/optimize from there.

Typically you set the EL and the POL, then sweep right and left (AZ) in small increments until the modem finds the satellite/transponder that you've set into the parameters. Then you fine tune the EL, then go back and fine tune the AZ. You may have to do this more than once. If you were in the states, you'd then optimize the POL by using the modem ACP capability. But I doubt you get that option from the Iraqi provider. You can try to tweak the POL to see if it increases the signal strength any. But don't hold your breath. Alternatively, contact the provider and ask if they're equipped to assist you optimize crosspol. If yes, it's a real time process (it's done over the phone). They'd have to observe your TX signal on a spectrum analyzer while you adjust the POL at your end.

//greg//

Powered by YaBB 2.5.2!
YaBB Forum Software © 2000-. All Rights Reserved.