Pages: 1

PES 5000 Manual Setup Instructions

(Read 20242 times)

Ex Member

Ex Member

Aug 17^th, 2007 at 11:43pm

I have inherited a poorly setup network and would like some information on how to properly setup a satellite broadband connection. We currently have a Hughes PES 5000 modem directly connected to a server. It serves as the main internet connection for all of the transaction processing here.

First, is it possible for this modem to be connected to a router, or does it have to be plugged directly into the server. Second, there is a parallel port cable running between the modem and the server. Is this simply a cable to allow for shell access on the modem. If so, can I disconnect it with no ill effect?

Finally, does anyone know of a manual for this model or a similar model modem?

Back to top

« Last Edit: Jul 11^th, 2015 at 11:29am by Admin1 »

IP Logged

union

Member
★★
Offline

Posts: 8

Reply #1 - Aug 18^th, 2007 at 10:17am

Hi,

The PES 5000 can be connected via a router if needed, the PES 5000 gets its IP address from the NOC so you would need to know the range you can use, the parallel port rs232 would have been used/is used for connection to on site equipment and is not used for shell access. Access to the PES is via a rj11 to serial cable connected to the config port on the rear of the unit using DIU editor software. The PES general ref manual is a 10 meg PDF file I have a copy and can upload it to a free file server if you need a copy. Just let me know.

Union

Back to top

IP Logged

Ex Member Ex Member	Reply #2 - Aug 18^th, 2007 at 7:24pm PM sent.
Back to top	IP Logged

union Member ★★ Offline Posts: 8	Reply #3 - Aug 20^th, 2007 at 6:39pm Replied to PM
Back to top	IP Logged

scooterz56 Member ★★ Offline Posts: 24	Reply #4 - Sep 14^th, 2007 at 6:06pm Doesn't the 5000 max out at 256 upload? That Gen Ref Manual is a HONKER ain't it, 797 pages!
Back to top	IP Logged

Ex Member Ex Member	Reply #5 - Feb 7^th, 2008 at 2:35pm Would I be able to get a copy of the PES 5000 manual as well?
Back to top	IP Logged

USN - Retired YaBB Moderator ★★★★★ Offline Posts: 837 Kentucky (USA)	Reply #6 - Feb 7^th, 2008 at 6:07pm Doubt you're going to be able to find the big book available for download, but here's a couple links to abridged versions: * Edited by forum admin 24/9/2014.� These old links now fail * � comtm.com/download/install_Galaxy2.pdf and � evsig.com/docs/Hughes/Galaxy/PES5000%20config.doc //greg//
Back to top	« Last Edit: Sep 24^th, 2014 at 1:04pm by Admin1 » USN (Ret) IP Logged

scooterz56 Member ★★ Offline Posts: 24	Reply #7 - Feb 7^th, 2008 at 10:19pm PES 5000 is Narrow Band equipment, you cannot do a Broadband connection thru a 5000.
Back to top	IP Logged

Eric Johnston Senior Member ★★★ Offline Posts: 2109	Reply #8 - Sep 18^th, 2014 at 7:57pm The two links above no longer work. Does anyone have links to PES 5000 manuals ? Best regards, Eric
Back to top	IP Logged

RF Network Solutions Member ★★ Offline Posts: 2	Reply #9 - Sep 21^st, 2014 at 5:53am Hi, I am looking for the PES5000 Hughes IDU Operational Manual. Please provide. Regards Rajesh
Back to top	IP Logged

RF Network Solutions Member ★★ Offline Posts: 2	Reply #10 - Sep 21^st, 2014 at 5:54am Hi Again, Actually I would like to test the Hughes 2W Ku band ODU at Bench RF Test up to see the Max Power ( 2W) at Spectrum Analyser. I am not able to find any command to initiate from DIU SW to raise the pure carrier to see the power at Spectrum Analyser or Power Meter Regards
Back to top	IP Logged

Admin1 YaBB Admin ★★★★★ Offline Posts: 1206	Reply #11 - Sep 21^st, 2014 at 7:17pm If you are able to get the command line interface working then it might be worth trying to get the modem to tell you the list of possible commands and then try one that looks romising. Try these to start, plus any other ideas you might have. h -h help -help /? -? ?/ man Best regards, Eric.
Back to top	« Last Edit: Sep 22^nd, 2014 at 10:14pm by Admin1 » WWW IP Logged

fhoezhinks

Member
★★
Offline

Posts: 1
Indonesia

Reply #12 - Oct 15^th, 2014 at 10:41am

Quote:

Hi Again, Actually I would like to test the Hughes 2W Ku band ODU at Bench RF Test up to see the Max Power ( 2W) at Spectrum Analyser. I am not able to find any command to initiate from DIU SW to raise the pure carrier to see the power at Spectrum Analyser or Power Meter

Regards

Hi, Hope this can help

- Open DIUCE 555
- Tab Utils
- Terminal
� �enter below command :
� �- x5
� �- q7B10� <-- {where 7B10 is hexa value for center RF}
� �- x0
� �- x9

Regards,
Fhoezhinks

Back to top

« Last Edit: Oct 15^th, 2014 at 3:27pm by fhoezhinks »

IP Logged

KoredeE Member ★★ Offline Posts: 1	Reply #13 - Jul 9^th, 2015 at 10:15pm Oh thank God I finally got someone with this doc. I do have this doc in time past but it went with a crashed hard drive. Pls do help me with it I can be reached at esankorede@yahoo.com Thanks.
Back to top	IP Logged

Admin1 YaBB Admin ★★★★★ Offline Posts: 1206	Reply #14 - Jul 11^th, 2015 at 11:28am I have put it here: https://www.satsig.net/pdfs/PES-General-Reference-Manual.pdf Please note it is 10.4 Mbytes. Download once, carefully, and save the pdf file locally for future reference. Best regards, Eric.
Back to top	WWW IP Logged

Pages: 1

Send Topic | Print