Advertisment: Broadband via satellite
Advertisment: Planet Earth rotating animation

Satellite Internet Forum.

Welcome, Guest.        Forum rules.
      Home            Login            Register          
Pages: 1

Connecting Tooway Modem via Network Router

(Read 29429 times)
Ex Member
Ex Member

Nov 9th, 2008 at 6:40pm  
I have a D-LInk DIR-655 wireless router.
As usual, it has an IP address of
Connecting two or three pc's to the network works fine (using the LAN ports on the router) - one of the PC's is a laptop, connected via the wifi.
Everything works normally.

But I cannot get the network to see the Tooway modem, and therefore the internet.

I've tried connecting the modem via a LAN port and the WAN port (on the Router), but with no success.
All PC's are set up for automatic IP address and DHCP is enabled.

If the modem is connected directly to a PC, excluding the network in other words, it works perfectly.

I feel I must be making a very basic error - can anyone assist and point me in the right direction please?

Back to top
IP Logged
Eric Johnston
YaBB Moderator

Posts: 2109
Reply #1 - Nov 9th, 2008 at 8:48pm  
You need to find the operational IP address and subnet of your Tooway modem.  It is likely that your service provider has already told you this.  e.g.

This means that you have a network ready at the ethernet port on the Tooway.  An example network is called  The gateway is  You can connect only one PC with You also have a multicast address  The .252 inn the subnet mask means that a total of 4 IP addresses exist. (.248 would mean a total of 8 IP addresses, with 5 of them available for PCs)

Read more about  This will help your understanding if your Tooway has an IP address not ending in 1 or a mask not ending in 252

Check by connecting a PC direct to the Tooway modem.  The PC needs to have the same subnet mask as the modem e.g, the gateway is the Tooway modem IP address e.g. and the IP address of the PC needs to be different, eg

Use two DNS servers as told to you by your service provider.

Open a DOS command prompt window and type ipconfig /all  Write down the information.

Having understood the modem connection and successfully accessed the internet, connect your router WAN port to the modem.  Your PC needs to be connected to the router via one of the LAN ports.  The IP address of your PC now needs changing to match the LAN network which you invent.  You have already invented your LAN, presumably name=  Router gateway  You are using DHCP bu you could allocate each PC in the range upwards. The number of PCs you may connect will be 253 if the you use the default subnet mask

Your router manual is here (note 7.9 Mbytes file size)

If someone reading this has a Tooway modem, please add your sugegstions and say if I am right or wrong.

Best Regards, Eric
Back to top
« Last Edit: Nov 10th, 2008 at 8:59am by Admin1 »  
IP Logged
Ex Member
Ex Member

Reply #2 - Nov 21st, 2008 at 12:05am  
Thanks for the reply Eric.

This has now been solved.

To cut a long story short:
I changed the ADSL router for a Cable/DSL one - the D-LINK DIR 635.

It only works with a Crossover cable.

Then it was simple - plug the Tooway modem into the Internet socket and off it went, no need for any configuration at all.

The Wifi LAN is brilliant on this router, being the Draft n version. It connects at 130 Mbps and even works all the way down the garden!

Back to top
IP Logged
Senior Member

Posts: 65
Reply #3 - Nov 21st, 2008 at 11:02am  
Sean, glad to know that solved the problem. For Tooway clients thinking of using wireless, please invest in a cable/DSL router opposed to ADSL.
Back to top a high-speed Satellite Internet solution that delivers fast and reliable internet to difficult to connect spots around the world.
IP Logged
Ex Member
Ex Member

Reply #4 - Nov 23rd, 2008 at 6:50pm  
I've installed quite a few Tooway systems in Southern Spain and our customers usually require a wireless network in their home as well.

We have been using the SMC Barricade SMCWBR14-G2 Cable/DSL router and it works like a dream - very reasonably priced too.

One thing I noticed early on was that you can't "hotswap" the router onto the Tooway modem if you have already connected a PC previously - you have to power off the modem, then plug in the router and then power on again. After this, you can connect as many wired and wireless devices as you like, with the router doing all of the DHCP work with a 192.168.2.x subnet.
Back to top
IP Logged
Pages: 1